Time-Resolved Fuel Density Profiles of the Stagnation Phase of Indirect-Drive Inertial Confinement Implosions.

The implosion efficiency in inertial confinement fusion depends on the degree of stagnated fuel compression, density uniformity, sphericity, and minimum residual kinetic energy achieved. Compton scattering-mediated 50-200 keV x-ray radiographs of indirect-drive cryogenic implosions at the National Ignition Facility capture the dynamic evolution of the fuel as it goes through peak compression, revealing low-mode 3D nonuniformities and thicker fuel with lower peak density than simulated. By differencing two radiographs taken at different times during the same implosion, we also measure the residual kinetic energy not transferred to the hot spot and quantify its impact on the implosion performance.

Streaming MASSIF: Cascading Reasoning for Efficient Processing of IoT Data Streams.

In the Internet of Things (IoT), multiple sensors and devices are generating heterogeneous streams of data. To perform meaningful analysis over multiple of these streams, stream processing needs to support expressive reasoning capabilities to infer implicit facts and temporal reasoning to capture temporal dependencies. However, current approaches cannot perform the required reasoning expressivity while detecting time dependencies over high frequency data streams. There is still a mismatch between the complexity of processing and the rate data is produced in volatile domains. Therefore, we introduce Streaming MASSIF, a Cascading Reasoning approach performing expressive reasoning and complex event processing over high velocity streams. Cascading Reasoning is a vision that solves the problem of expressive reasoning over high frequency streams by introducing a hierarchical approach consisting of multiple layers. Each layer minimizes the processed data and increases the complexity of the data processing. Cascading Reasoning is a vision that has not been fully realized. Streaming MASSIF is a layered approach allowing IoT service to subscribe to high-level and temporal dependent concepts in volatile data streams. We show that Streaming MASSIF is able to handle high velocity streams up to hundreds of events per second, in combination with expressive reasoning and complex event processing. Streaming MASSIF realizes the Cascading Reasoning vision and is able to combine high expressive reasoning with high throughput of processing. Furthermore, we formalize semantically how the different layers in our Cascading Reasoning Approach collaborate.

Energy penetration into arrays of aligned nanowires irradiated with relativistic intensities: Scaling to terabar pressures.

Ultrahigh-energy density (UHED) matter, characterized by energy densities >1 × 108 J cm-3 and pressures greater than a gigabar, is encountered in the center of stars and inertial confinement fusion capsules driven by the world's largest lasers. Similar conditions can be obtained with compact, ultrahigh contrast, femtosecond lasers focused to relativistic intensities onto targets composed of aligned nanowire arrays. We report the measurement of the key physical process in determining the energy density deposited in high-aspect-ratio nanowire array plasmas: the energy penetration. By monitoring the x-ray emission from buried Co tracer segments in Ni nanowire arrays irradiated at an intensity of 4 × 1019 W cm-2, we demonstrate energy penetration depths of several micrometers, leading to UHED plasmas of that size. Relativistic three-dimensional particle-in-cell simulations, validated by these measurements, predict that irradiation of nanostructures at intensities of >1 × 1022 W cm-2 will lead to a virtually unexplored extreme UHED plasma regime characterized by energy densities in excess of 8 × 1010 J cm-3, equivalent to a pressure of 0.35 Tbar.

The FAST module: an add-on unit for driving commercial scanning probe microscopes at video rate and beyond.

We present the design and the performance of the FAST (Fast Acquisition of SPM Timeseries) module, an add-on instrument that can drive commercial scanning probe microscopes (SPM) at and beyond video rate image frequencies. In the design of this module, we adopted and integrated several technical solutions previously proposed by different groups in order to overcome the problems encountered when driving SPMs at high scanning frequencies. The fast probe motion control and signal acquisition are implemented in a way that is totally transparent to the existing control electronics, allowing the user to switch immediately and seamlessly to the fast scanning mode when imaging in the conventional slow mode. The unit provides a completely non-invasive, fast scanning upgrade to common SPM instruments that are not specifically designed for high speed scanning. To test its performance, we used this module to drive a commercial scanning tunneling microscope (STM) system in a quasi-constant height mode to frame rates of 100 Hz and above, demonstrating extremely stable and high resolution imaging capabilities. The module is extremely versatile and its application is not limited to STM setups but can, in principle, be generalized to any scanning probe instrument.

Preplasma conditions for operation of 10-Hz subjoule femtosecond-laser-pumped nickel-likex-ray lasers.

We present measurements of electron densities of plasmas with femtosecond (fs) temporal resolution. The plasmas are generated by laser pulses with different intensities at different time delays. Such plasmas are of great interest as preplasmas for transient, collisionally excited x-ray lasers. The laser pulses producing the plasmas are generated by stretching part of a 130-fs laser pulse of the ATLAS titanium-sapphire laser of our institute and focusing this radiation to a line on molybdenum and silver slab targets. The electron density is measured as a function of distance from the target by interferometry using a Wollaston prism. Using an ultrashort probe pulse allows one to obtain data extremely close, about 10 microm, to the target surface. Experimental data are compared with simulations using the MULTI hydrocode. The results allow comparison of the ablation from a hard (Mo) and a soft (Ag) material, optimization of prepulse-main pulse delay times, and selection of the best pump geometry allowing for propagation of the pump and x-ray beams. These points are key elements for the development of a high-repetition-rate soft-x-ray laser.